The D-ShakL2™ anchor can be mounted onto various surfaces and used in numerous ways – it is truly a universal anchor point. It is a 360-degree use anchor. Unlike other anchors, our forged D-ring is captured on the shackle with a spot-welded plate. This keeps the D-ring united with the anchor at all times, especially during installation in tough situations.

The anchor is only 4.5” x 2.0” and can be mounted on the exterior or interior of structures. It can be installed onto wood framing, concrete and metal structures for a permanent or temporary application. It is rated for 5,000 pounds and installs with ½” hardware (bolts/all-thread/concrete wedge anchors/poured in place concrete anchors/epoxy/field weld). The anchor can also be used in a horizontal lifeline application for up to 3 workers in fall restrain using our pre-made 3/8” cable lifelines.

The D-ShakL2™ is not designed as a roof mounted anchor point as there is no way to waterproof it. Exterior wood framed walls can be flashed, and concrete/masonry walls require caulking on the edges. Fasteners are supplied by customer. A separate anchor can be used as a backer plate or the installer can use washers to secure the backside of the anchor point. Backer plates are also available.

  • STRUCTURE ATTACHMENTS: Wood Beams, Wood Trusses, Steel Decking, Structural Steel, Concrete, etc.
  • STRUCTURE CONFIGURATION: Walls, Ceilings, Floors, Roof Field, Flat, Vertical and Upside Down
  • ATTACHMENT HARDWARE: ½” Grade-8 Bolts, A-307 Threaded Rod, Concrete Wedge Anchors or Field Welding
  • FALL PROTECTION CONFIGURATIONS:
    • Stand Alone Anchor/Tie-Back Anchors for 1 person Fall Protection
    • Horizontal Lifeline System for 2 users in fall arrest from 10-20’ with multiple horizontal lines linked together using center/intermediate anchors.
    • Horizontal Lifeline System for 3 users in fall restraint from 10-20’ with the option of multiple horizontal lines linked together using center/intermediate anchors.

Each D-shakL Anchor comes with a 2-page comprehensive Instruction/Specification Manual to cover most installation options. See the Engineering tab for comprehensive design/testing/engineering documents.

  • Complies with OSHA 1926:502 and 1910:140
  • 5,000-pound Minimum Strength
  • Numerous Mounting Options Available
  • Can be used to mount Vertical Lifeline or SRL’s
  • Stand Alone Anchors or Use in Horizontal Lifeline System
  • Large Inventory in Stock
  • Engineered Design for Easy Compliance

Transparency: Do not use for window washing suspension, suspended work, scaffold tie-off or material lifting. Do not install with lag bolts or screws. Does not come with attachment hardware. Concrete wedge anchors and pour in place installations must be engineered by a competent or qualified person. Only SAS HLL systems are approved for use with the D-ShakL2™

  • WS Screws: You can use 2 ea. WS 3.5” screw through the 5/16” fastener holes in the D-ShakL2™ anchor as seen in Fig. 5A in the D-ShakL2™ addendum page. Anchor must be installed over a fully sheeted roof, wood beam or structure capable of withstanding the intended loads. No pre-drilling is necessary when using the WS Screws.

When installed with the above specified fasteners you can use the anchor for 1 person in fall arrest with a 30-degree service zone from each side of the anchor. When used in fall restraint you can apply the load in any direction when no free fall hazards are present.

Each D-ShakL2™ Anchor comes with a 2-page comprehensive Instruction/Specification Manual and Lag Bolt/WS-Screw addendum to cover most installation options. See the Engineering tab for comprehensive design/testing/engineering documents. WS Screws and Lag Screw fasteners cannot be reused. New fasteners must be used for each installation.

  • Complies with OSHA 1926:502 and 1910:140
  • 5,000-pound Minimum Strength
  • Numerous Mounting Options Available
  • Can be used to mount Vertical Lifeline or SRL’s
  • Use as a Stand Alone Anchor
  • Large Inventory in Stock
  • Engineered Design for Easy Compliance
D-ShakL2 Anchor with 180 degree rotating D-Ring
1029

Part #: 1029

Description:
D-ShakL2™ Anchor with 180-Degree rotating D-Ring, 2 bolt holes for 1/2″ mounting hardware.

UPC: 786158102901

316sst D-ShakL Anchor
1029-S

Part #: 1029-S

Description:
316sst D-ShakL Anchor w/304sst D-Ring.

UPC: 786158102918

20-pack 18-8 3/8in x 3.0in stainless steel lag bolts
2080S-3.0

Part #: 2080S-3.0

Description:
20-pack 18-8 3/8″x3.0″ stainless steel lag bolts.

UPC: 786158208009

20-pack 18-8 3/8in x 3.0in stainless steel lag bolts
1335

Part #: 1335-10

Description:
10′ 30° cable with snap-hooks.

UPC: 786158133509

Part #: 1335-12

Description:
12′ 30° cable with snap-hooks.

UPC: 786158133516

Part #: 1335-14

Description:
14′ 30° cable with snap-hooks.

UPC: 786158133523

Part #: 1335-16

Description:
16′ 30° cable with snap-hooks.

UPC: 786158133530

Part #: 1335-18

Description:
18′ 30° cable with snap-hooks.

UPC: 786158133547

Part #: 1335-20

Description:
20′ 30° cable with snap-hooks.

UPC: 786158133554

    Request more Information about the D-ShakL2™ Anchor - Lag Screw: